Hubei Nuojin Sen Technology Co.,Ltd
5 1

Black Color PCB Printing Ink , 2H Hardness Photoimageable Etch Resist

Contact Now* Send an Inquiry to this supplier.
or
Start Order * Name your price
You may also be intersted in
industrial marking ink

Contact us

Hubei Nuojin Sen Technology Co.,Ltd
[China]

Address
29th floor room 15 No.5 Commercial building B block ,the 2nd section Wuchang Fu west,No.32 Wenzhi street,Hongshan district,Wuhan city,China Wuhan Hubei
Phone
86-027-87874388
Contact name
Manager

Quick Information

  • Brand Name: NUOJINSEN
  • Place of Origin: China
  • Model Number : NJS

Description

Black color etching resist ,photoimageable ink for industry use

APPLICATION and END-USE DESIGN:

 

It is a versatile Etch/Plating Resist used on high volume Print and Etch boards where a fast rate of throughput per hour is required, and which is governed by the squeegee speed and the cure rate, and where the sharpest definition is sought with rapid stripping after etch.

 

It can be used to resist Alkali Etchants in the pH range 8.0 to 9.5 it can also be used as an Acid Etch Resist, and is excellent as a Plating Resist, capable of withstanding up to 40 amperes and high pH solutions above a pH of 8.0.

 

 

FEATURES and ADVANTAGES

 

1. It is capable of almost Universal application. Its excellent printing characteristics and screen stability offer the opportunity for use on hand, semi- and fully-automatic machines.

2. It strips cleanly, without residue on the boards.

 

3. It resists both Plating baths, Alkali and Acid Etchants, Acid Copper and Tin Lead Plating baths. Pre-cleaners with pH under 10.0 can safely be used.

 

4. Strong blue colour gives good contrast against the copper and the hard surface produced on curing resists abrasion and mechanical damage during automatic stacking.

 

5. High Thixotropy index produces sharp vertical image edges when screening even fine lines of 200 to 300 micron width.

 

6. It is formulated from materials which are fully compatible, thus avoiding entirely bleed out onto the copper non-image areas.

 

7. Fast removal in alkaline solutions.

VISCOSITY ADJUSTMENT

It is supplied press-ready. It is desirable to print it too thick rather than too thin, otherwise edge definition could suffer. ER1 is recommended in amounts up to 5%.

 

 

BOARD CLEANING

 

It is necessary to clean the copper surfaces of boards to remove all oxides and grease from the surface. Brushing is the usual method employed and this gives best adhesion of the etch resist.

 

 

PRINTING

 

Print through 77 - 120T or S polyester mesh or the equivalent in Stainless Steel. Consult the screen mesh manufacturer to select the right combination of mesh open area relative to circuit design to avoid "moire" effect on imaging.

 

Use a Direct/Indirect or Capillary stencil with a 18 to 20 micron stencil thickness below the screen mesh when used as an Etch Resist, and 35 to 50 when used as a Plating Resist, is recommended.

 

Use a relatively hard polyurethene squeegee of up to 70 to 80 degree shore hardness as Etch Resist, 65 to 70 when used as a Plating Resist.

 

 

DRYING

 

Infra-Red or Convection ovens with strong exhaust systems are recommended.

 

5-10 minutes at 120 degrees C, or 10-15 minutes at 90 degrees C will give a hard film.

 

REMOVAL

 

The resist mask can be removed under spray-jets in solutions of caustic soda or potash of between 2-5% concentration at temperatures of 40 - 50 degrees C. Alternatively, a 30 - 60 second dip in static tanks containing 10% NaOH solution, followed by a water-spray, will be effective.

 

The pH of the stripping solution should be in excess of 11.5 in order to obtain optimum results.

 

SCREEN CLEANING

 

Screens can be cleaned with Universal Screenwash SW100.

STORAGE

 

Store between 10-25 degs C in a dry store.

 

Avoid subjecting containers to temperatures below 5 deg C because of the risk of splitting.

 

Normal stock rotation should be carried out although useful life will reach 1 year under normal storage conditions. The lid on opened cans should be firmly sealed.

 

 

Our company:

 

Hubei Nuojinsen Technology Co.,Ltd ,after years of unremitting efforts,Combined with foreign advanced technology and process,Production of PCB ink has reached the technical level, conforms to the requirement of RoHS environmental protection directive, with excellent quality and excellent service is deeply trusted by customers.


Product Image

  • Black Color PCB Printing Ink , 2H Hardness Photoimageable Etch Resist image

Send an Inquiry to this supplier

Send an Inquiry to this supplier
* From
  To Manager
Hubei Nuojin Sen Technology Co.,Ltd
* Buying Product
- Please enter your specific buying item.
e.g. 42 inch LCD TV, leather executive chair
Category : Other Passive Components
* Message

Use English only Max. 2000 characters. (Min. 20)

Send
EC21.com does not guarantee the validity of product information or the credentials of sellers.